Locomotive Prints/Parts
General Locomotive Parts/Upgrades
G Scale Bachmann Annie USA Trains Smoke Adapter by Rob859
Bachmann Annie USA Trains Smoke Adapter.
This adapter allows you to mount a USA Trains smoke generator into a Bachmann Annie Locomotive. Use (2) M2*10 self tapping screws to mount adapter to smoke generator. Note the orientation of the eccentric mounting nuts. Adapter assembly mounts inside loco…
This adapter allows you to mount a USA Trains smoke generator into a Bachmann Annie Locomotive. Use (2) M2*10 self tapping screws to mount adapter to smoke generator. Note the orientation of the eccentric mounting nuts. Adapter assembly mounts inside loco…
www.thingiverse.com
General USA Trains Locomotive Parts/upgrades
USA Trains Replacement Parts by ShadowVFX
These were designed for and printed on a resin printer. I am not sure how well these will print on a filament printer. Adjustments and scaling may be necessary for proper fit and alignment.
These are common replacement parts for the USA Trains diesel locomotives. Mainly the GP7/9, GP30 and GP38. I w…
These are common replacement parts for the USA Trains diesel locomotives. Mainly the GP7/9, GP30 and GP38. I w…
www.thingiverse.com
USA Trains SD40 Parts/Upgrades
USA Trains SD70 Parts/Upgrades
USA Trains GP7/9 Parts/Upgrades
USA Trains GP38-2 Parts/Upgrades
USA Trains GP38-2 Flared Radiator by manimal
Yes, I know this doesn’t exist. But it’s MY railway and I’ll do what I want! I designed this flared radiator shroud to fit over the body of a USA Trains GP38-2 without permanent modification. You will need to pop out the existing air intakes, long grab bar and rear lift rings though.
Note: You wi…
Note: You wi…
www.thingiverse.com
COMFORT CAB FOR USA TRAINS GP38-2 by manimal
This is a direct fit for the USA Trains GP38-2. It slides over the long hood and is fastened with the same screws as the standard cab. You will need to cut the 2 sections indicated.
The biggest challenge in making a nice model with FDM printing is getting rid of the layer lines to enable a smooth f…
The biggest challenge in making a nice model with FDM printing is getting rid of the layer lines to enable a smooth f…
www.thingiverse.com
USA Trains F3 Parts/Upgrades
USA Trains NW2 Parts/Upgrdes
USA Trains EMD NW2 roof mounted Air Reservoirs by manimal
Hood mounted air reservoirs for USA Trains 1:29 scale NW2 locomotive.
The tanks are 16mm polystyrene test tubes. I measured 100mm from the open end and cut off the bottom. There is a bit of a taper hence the 2 different sized caps and brackets. The piping is 14 gauge wire and Evergreen polystyren…
The tanks are 16mm polystyrene test tubes. I measured 100mm from the open end and cut off the bottom. There is a bit of a taper hence the 2 different sized caps and brackets. The piping is 14 gauge wire and Evergreen polystyren…
www.thingiverse.com
General Bachmann Locomotive Replacement/Upgrade Parts
Aristo-Craft/Bachmann Dash 9 Replacement/Upgrade Parts
GE Dash 9 Locomotive by rangerjoel
This is a Beta version of a G Gauge General Electric Dash 9 Locomotive.
The individual parts are designed to be printed on a 20 x 20 cm builders plate like that found on an Ender 3.
The base plates are held together with M3 bolts running thru a 1.25 x .25″ steel bar that serves as the support for th…
The individual parts are designed to be printed on a 20 x 20 cm builders plate like that found on an Ender 3.
The base plates are held together with M3 bolts running thru a 1.25 x .25″ steel bar that serves as the support for th…
www.thingiverse.com
LGB Replacement/Upgrade Parts
Aristo-Craft RS3 Replacement/Upgrade Parts
Aristo-Craft C-16 Parts/Upgrades
General Aristo-Craft Parts/Upgrades
Aristo-Craft U25B Replacement/Upgrade Parts
Rolling Stock
Rolling Stock Parts/Upgrades
Caboose Roller Bearing Sideframe with Generator by MortimerTrainBrain
I saw the caboose trucks by 512 Designs, but realized that to be more accurate, it needs a generator under the caboose. I have created a ‘close enough’ generator based upon pics provided by others and found on the internet. This side frame is also set up to accept a 630ZZ ball bearing.
Credit to t…
Credit to t…
www.thingiverse.com
Barber S2 Roller Bearing Trucks by mrpictovid
Replacement side frames for USA Trains G scale freight trucks. These were adapted from the files uploaded by raby to make fully sprung trucks. I did resize the pockets in the side frames to accept 3x6x2.5 mm flanged ball bearings. You may need to slightly polish the factory USA axle ends to get them…
www.thingiverse.com
1:29 G GAUGE USA TRAINS COMPATIBLE TRUCKS by 512Designs
Truck side frames and bolsters that are fully compatible with USA Trains products. Fits any 3mm axle wheelsets and USA trains couplers (can use Kadee conversion couplers too).
More side frame models planned.
3D PRINTING SETTINGS
Sideframes:
-Archbar (FDM or resin printer)
-Caboose Roller Bearing (Re…
More side frame models planned.
3D PRINTING SETTINGS
Sideframes:
-Archbar (FDM or resin printer)
-Caboose Roller Bearing (Re…
www.thingiverse.com
Printable Tools
Three Point Track Gauge by TrotFox
A pair of track laying gauges for the insane among us who hand-spike track. These are setup for code 250 Llagas Creek rail (3.5mm width railhead.) I have included 45mm gauge and 70.64mm gauge versions for those of us who are further afflicted with the need to model standard gauge in F scale.
Surpris…
Surpris…
www.thingiverse.com
USAT Axle Repair: A Collection by mrpictovid
Check out mrpictovid’s collection USAT Axle Repair: Four useful tools for USA Trains G Scale locomotive motor blocks. Designed and uploaded by ereuter two of which are remixes of his originals by Michael45013. The remixed versions allow extra clearance for brass tubing if you are putting sleeves cra…
www.thingiverse.com
Mini Sanding Block – Jewelers – Pen Making – Model Building by tswalter
I make a lot of small handmade items that require quite a bit of sanding. Holding small pieces of sandpaper is difficult and to try to get a backing for the paper is even more difficult. After a long bout of sanding metal strips for making pen clips I came up with this idea. The basic design is simi…
www.thingiverse.com
